- DSC DLS SOFTWARE DOWNLOAD INSTALL
- DSC DLS SOFTWARE DOWNLOAD UPGRADE
- DSC DLS SOFTWARE DOWNLOAD CODE
- DSC DLS SOFTWARE DOWNLOAD PLUS
- DSC DLS SOFTWARE DOWNLOAD SERIES
While e-learning won't replace traditional classrooms, it will change the way we know them today. And other studies show that students taking courses online score better on standardized tests.Ĭan online education replace traditional education?
i've set the time delays for the partitions to 0 but still i have a 30 second wait on the arming using either the control panel or the remote.Students participating in online classes do the same or better than those in the traditional classroom setup.
DSC DLS SOFTWARE DOWNLOAD PLUS
Plus after the reset and reprogramming the original 8 zones i have a delay arm all of a sudden. Tell us the results of this last step.Īfter following the instructions above i still see the same results module registers but not reporting/triggering correctly on the zones. If it is, use the arrow key to scroll through the open zones note which zones are open. If it does NOT say ZONES 17-24, stop and report back.ĭefine zones 1-8 as null ( *8 IC 001 00 00 00 00 00 00 00 00 # ). Keypad should read: ENROLLED MODULES KEYPAD 8 ZONES 17 TO 24. Set jumpers 1, 2, and 3 to ON OFF ON (for zones 17-24). Keypad should read: ENROLLED MODULES KEYPAD 8.
DSC DLS SOFTWARE DOWNLOAD CODE
Set system clock (*6 Master Code 1 hhmm mmddyy #)ĭefault the system (*8 Installer's Code 999 IC 999 # ). Remove everything connected to the board except the AC transformer connection, battery, one PK5500 keypad.
It could possibly help us to pinpoint the problem by eliminating variables. If you're willing, we can try to narrow down the possibilities by going back to square one, then proceeding one step at a time. Ken_in_Pittsburgh suggested the following: ( but for testing only connecting 1 module ) I then got onto the internet and i came across a thread with the following steps. Yet the system didnt register the Open zone of the door contact nor did it recognize the Panic button. I configured the zoning definitions of 001 and 002 marking all unused channels as 00 and for testing i assigned zone 9 as 03 with a door contact( fitted with 5.6k resistor) and zone 17 as 16 for a panic button( fitted with 5.6k resistor). After each installation i did the 902 code waited a minute and check unit was indeed supervised using 903.Īfter the installation of the last Module the following Supervised modules showed on the system:Īnd this is where the train got of the tracks.
DSC DLS SOFTWARE DOWNLOAD INSTALL
I proceeded to install both Expander modules with zones 8-16 and 17-24 configured respectively and all zone populated with a 5.6k resistor. I installed the PK5500 Keypad with very little hassle did a *8 IC 902 to remove the old keypad and clear the fault codes.
DSC DLS SOFTWARE DOWNLOAD UPGRADE
with this said i started to research the DSC systems and came across the DSC PC5108 ver2 Expansion modules and saw i can upgrade the keypad to an alpha numeric PK5500 LCD keypad.ĭoing the sums it worked me out considerably cheaper to purchase 2 expansion modules and the keypad, and additional 2 PIR's a few recessed door contacts and 2 sets of Centurion i5 beams. they came back with some funny number which made it cheaper just to install a new alarm system. This was all and well then i got an alarm company to quote me on a armed response services and asked them to upgrade my system. Panic Buttons (Zone Definition 16 24 hour panic alarm) Kitchen Door (Zone Definition 03 Instant alarm) Garage Door (Zone Definition 03 Instant alarm) Kitchen and Main Bedroom ( PIR's) (Zone Definition 05 Stay alarm) Study ( PIR ) (Zone Definition 03 Instant alarm)įront door (Zone Definition 03 Instant alarm) TV Room ( PIR ) (Zone Definition 03 Instant alarm) Wendy house ( PIR ) (Zone Definition 03 Instant alarm)
DSC DLS SOFTWARE DOWNLOAD SERIES
I recently bought a house that was fitted with a PS1808 Alarm system.įitted to this Alarm system was the following:Įvolution Series EV-KT1 wireless remote system ( reads as a DSC 5132 on the alarm )Īll the above was configured into 1 Partition with the following Zone configuration:
0 kommentar(er)
